• A way to modify indicators for TR Sidescreen when R&P Steering is fitted

    I dont think the pictures got transfered. Email me if you want them
    SIDESCREEN TR – TURN SIGNAL INDICATOR AND HORN CONVERSION

    When, during a long telephone conversation, I was negotiating the purchase of the 1958 TR3A, with a guy in Perth, he was telling me that the steering was in A1 condition. That statement made me just a little suspicious because over the years I have owned a few of these cars and found the steering quite prone to wear.
    I eventually went down to Sydney and picked the TR up from the trucking depot, washed off the Nullarbor Plains Sand and proceed to drive it home, across the Blue Mountains.
    During my Evil Knievel type negotiation of the hairpin bends I just knew that the guy wouldn’t pass his Boy Scouts Truth Badge. Then again he was trying to sell it and he was located some 4000 KM away so why not guild the Lilly just a little, or even a lot!
    When I eventually settled down, after that Kamikaze drive, I decided to convert the original single tube steering with a Moss Rack and Pinion Kit.
    I bought a Moto-Litre Steering wheel with the Boss to suit the original TR central Hub and Horn Button arrangement and I knew that it would not be possible to maintain the indicator and Horn Button system. I couldn’t find much out about how others had tackled the problem so the way I figured it out is as follows. It may be of interest.
    Firstly purchase an MGB / Mini combination Trafficator, Horn Push, Headlight Dip and Headlight flash unit. Lucas Part No 39309.

    Drill and Tap Shaft for Dome Nut
    The Moss outer steering tube and inner steering shaft end up, with some fiddling for correct adjustment, in a very good relationship for mounting the Lucas unit on the end of the Tube and the Steering Wheel having just an exact amount of clearance at the bottom of the boss not to foul the Switch.

    MGB Shroud in position
    A 6.5mm hole needs to be drilled at the end of the Tube in order to locate the Switch in a non rotational locking position.
    A 4mm Dome Nut with the threaded part of a matching screw, with head cut off, will act as a cancellation button. This is achieved by drilling and Tapping the Steering Shaft in the correct position and with the aid of Locktite, mount the Dome Nut so it will never vibrate out.
    An MBG Shroud, with some modifications, will house the Lucas Switch. The Shroud needs to be shortened, as shown, but by doing this you lose the bottom two screws, with imbedded nuts, that hold the two halves together.
    This can be overcome by making an Aluminium bracket, mounted with the aid of three Screws. One Screw locates to the Steering Tube and the other two hold the two halves together at the bottom end.
    A little bit of reliving of the Plastic is also required to clear the Speedometer Glass Face.
    If you really want to bring the car into the 1990’s you can remove the foot operated Headlight Dimmer and transfer the wiring to the Lucas Switch as well as giving you a Horn Push and even a Headlight Flash which saves one lifting a finger from the Steering Wheel in order to give recognition to that oncoming TR.
    Certain Relays are required for this and in my opinion the introduction of some much needed additional fuses and other operating Relays makes the car very thankful.

    I am only too pleased to offer any other comments or assistance if required.
    Ian Simmons
    RYLSTONE NSW
    AUSTRALIA

    Aluminium Bracket
    Aluminium Bracket
    secsimmo@bigpond.com







    Cut off MGB Shroud
    Dome Nut


    Cut off MGB Shroud
    Cut off MGB Shroud
    Cut off MGB Shroud
    Cut off MGB Shroud






  • Recent Articles

  • Recent Forum Posts

    F Schreiber

    Re: Which Original Oil filter assembly for BN7

    Well, I wonder why the AEC 675 is listed in the Service Parts list, its the last one on the list, and the parts listing unclear to me any details about

    F Schreiber Today, 11:29 AM Go to last post
    Hill Billy

    Re: Sandy's TR 3

    Oil canning can drive a person to drink. I've spent many hours working them out. Tried many different methods. The small shrinking disc seemed to work

    Hill Billy Today, 10:35 AM Go to last post
    SherpaPilot

    Re: Steering Column Loose

    Good Morning Andy, My TR6 has a teak-wood dash panel. It provides a hole for the column to pass through. The entire panel would require removal to follow

    SherpaPilot Today, 10:30 AM Go to last post
    dezand

    Re: Which Original Oil filter assembly for BN7

    I believe there are only two options, Tecalemit (1B2897) or the Purolator (AEC897)
    My BT7 was built in Nov 1959 and has the Purolator.

    dezand Today, 10:27 AM Go to last post
    DavidApp

    Re: Sandy's TR 3

    Hello Bill

    Looking good.

    A fit to the tub is a great idea.
    I did the John patch, welded it in the wing then when I fitted

    DavidApp Today, 10:27 AM Go to last post
  • Recent Blog Posts

    garystrumphet

    Garystrumpet

    My car has had its rear lever action shocks replaced with a Wheewlright tube shock conversion. The shocks are stamped made in england 010672. What shocks replace the ones I have? Where to find them?

    garystrumphet 06-09-2019 04:40 PM
  • Twitter