Results 1 to 8 of 8

Thread: Aluminum TR6 head.....

  1. #1
    Luke Skywalker
    Join Date
    Sep 2008
    Location
    Franklin, Louisiana
    Posts
    1,931
    Chats
    0

    Aluminum TR6 head.....

    Whatever happened to the development of the aluminum head for the TR6? I used to follow it on the web, some blokes across the pond were about to put it on the market. Have heard nothing of it in a while.
    Life is short. Don't look back.

  2. #2

    Re: Aluminum TR6 head.....

    mucho dinero!!! Modified Gas Flowed Cylinder Heads not sure if these are alloy or cast iron
    Frank J. Angelini
    Downingtown, PA
    TR3A TS58476LO The Grey Lady
    TR250 CD1510LO Demelza

  3. #3
    Jedi Knight
    Join Date
    Jan 2005
    Location
    Atlanta area
    Posts
    1,257
    Chats
    0

    Re: Aluminum TR6 head.....

    I hope they make it a cross flow.
    Just for fun

  4. #4
    Luke Skywalker
    Join Date
    Sep 2008
    Location
    Franklin, Louisiana
    Posts
    1,931
    Chats
    0

    Re: Aluminum TR6 head.....

    Quote Originally Posted by vettedog72
    I hope they make it a cross flow.

    Vettedog, where you been, cher?! You going to the show at Delgado in March?
    Life is short. Don't look back.

  5. #5
    Yoda tomshobby's Avatar
    Join Date
    Apr 2006
    Location
    Windsor, Wisconsin
    Posts
    3,648
    Chats
    0

    Re: Aluminum TR6 head.....

    I've wondered about that too Bill.

    This is where it was posted but the site has not been updated for some time.

    http://www.canleyclassics.com/blog/a...1_archive.html
    Tom
    76 TR6
    74 Midget
    www.madbrits.org/
    www.mg3club.org/

  6. #6
    Great Pumpkin Brosky's Avatar
    Join Date
    Jul 2005
    Location
    S.E. MASS - USA
    Posts
    10,804
    Chats
    0

    Re: Aluminum TR6 head.....

    Probably due to a lack of C-A-S-H to fund such a project.
    Paul Rego
    S.E. MASS - USA
    1974 TR6 Mimosa & Chestnut
    Original Owner / Non Original Car
    1980 TR8 Lava Red Pearl / Tan
    New Owner / Non Original Car

    My TR6 Resto-Mod Project

  7. #7
    Yoda tomshobby's Avatar
    Join Date
    Apr 2006
    Location
    Windsor, Wisconsin
    Posts
    3,648
    Chats
    0

    Re: Aluminum TR6 head.....

    I am sure Paul is right. A little, by comparison, project I have going is going to cost enough. And not too long ago I had a run of castings made. Can't imagine what a project like a cylinder head might cost.
    Tom
    76 TR6
    74 Midget
    www.madbrits.org/
    www.mg3club.org/

  8. #8
    Yoda swift6's Avatar
    Join Date
    Jul 2005
    Location
    Fort Collins, Colorado USA
    Posts
    4,126
    Chats
    0

    Re: Aluminum TR6 head.....

    Quote Originally Posted by angelfj
    mucho dinero!!! Modified Gas Flowed Cylinder Heads not sure if these are alloy or cast iron
    For those prices I doubt they are alloy. The bare alloy heads were projected to be twice that with no work done to them.
    Shawn
    TR8FHC-Melted


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •