Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
BruceAllcorn
Senior Member
Offline
I've had an oil seal go bad on one of the half-shafts on my BJ8. Anyone know of a place to buy a bearing nut socket (2-3/16ths?) or a tried and true method to remove the bearing nut?
-
The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
-
Hey there Guest!
If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.**Upgrade Now**
(PS: Subscribers don't see this UGLY banner)
BJ8 Half-Shaft Oil Seal
- Thread starter BruceAllcorn
- Start date
Share this page
Offline
You can buy one from AH Spares: https://www.ahspares.co.uk/austin-healey/big-healey/Rear-Axle/SPANNER-hub-nut.aspx?¤cy=USD. The main reason for using the socket is to be able to tighten the nut to 100 - 150 lb-ft when replacing. Also remember that one side is left-handed thread.
D
Deleted member 21878
Guest
Guest
Offline
i was able to remove mine with a large set of channel lock pliers. you can get a good grip on the nut and the handles will fit between the lugs.
if you go the socket route, i believe it is a 8 sided nut. i got a 12 point one from amazon, i think, that worked well to tighten it back up. i could get it to 75 ft/lbs before it slipped off. but that was it. i can tell you that is much tighter than it was though.
the driver side wheel is a left handed thread.
if you go the socket route, i believe it is a 8 sided nut. i got a 12 point one from amazon, i think, that worked well to tighten it back up. i could get it to 75 ft/lbs before it slipped off. but that was it. i can tell you that is much tighter than it was though.
the driver side wheel is a left handed thread.
D
Deleted member 21878
Guest
Guest
Offline
oh and one other thing.
there are some previous threads on this.
it was recommended to me to change the bearing also as it has probably spun and caused the seal to get hot. i replaced both the seal and the bearing. i also did not replace the paper seal on the hub. i just used sealant.
search
https://www.britishcarforum.com/bcf/showthread.php?114219-BT7-rear-wheel-leaking
there are some previous threads on this.
it was recommended to me to change the bearing also as it has probably spun and caused the seal to get hot. i replaced both the seal and the bearing. i also did not replace the paper seal on the hub. i just used sealant.
search
https://www.britishcarforum.com/bcf/showthread.php?114219-BT7-rear-wheel-leaking
OP
BruceAllcorn
Senior Member
Offline
Thanks for the info. I have ordered the tool from AH spares and also ordered the wrench that Moss carrys. I had previously ordered a bearing as I figured since I was going to all the trouble I might as well replace the bearing as well.
Offline
I am not familar with the face of the socket that AH Spares sells but some socket ends are radiused and can slip off the thin bearing nut.
A trick is to surface grind the end of the socket perfectly flat so that it has full contact with the nut.
There is a lot of torque going on here
A trick is to surface grind the end of the socket perfectly flat so that it has full contact with the nut.
There is a lot of torque going on here
Similar threads
Similar threads
-
-
-
-
Wanted Looking for a used BJ8 switch panel.
- Started by Patrick67BJ8
- Replies: 5
-
-
-
Wanted WTB: 3.5 ratio diff/pumkin for '67 BJ8 Healey 3000
- Started by Scargo
- Replies: 0
-
-
-
-
-
-
-
-
For Sale 1967 Metallic Golden Beige MKIII BJ8 Numbers Matching - The Real Deal
- Started by BobMack
- Replies: 0
-
-
For Sale BJ8 disk wheel hubs, spindles & calipers- Started by BoyRacer
- Replies: 0
-
-
-
SOLD!! For Sale 1964 AH 3000 MkIII BJ8 Phase 1
- Started by suprgnat
- Replies: 2
-
-
-
-
-
-
-
-
-
For Sale Healey 3000 BJ8.... a restoration saga- Started by Cutrog1
- Replies: 0
-
-
-
-
-
-
-
Wanted Wanted: BJ8 Seat Track Sets (Both Sides)- Started by Mickey Richaud
- Replies: 5
-
-
-
-
-
BJ8 Intake manifold Booster & Vacuum Hookup threads sizes.
- Started by Patrick67BJ8
- Replies: 2
-
-
-
-
-
-
-
BJ8 transmission mainshaft bearing force needed to install/remove
- Started by AUSMHLY
- Replies: 1
-
-
A friendly reminder - be careful what links you click on here. If a link is posted by someone you don't know, or the URL looks fishy, DON'T CLICK. Spammers sometimes post links that lead to sites that can infect your computer, so be mindful what you click.