• The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
  • Hey there Guest!
    If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.
    **Upgrade Now**
    (PS: Subscribers don't see this UGLY banner)
Tips
Tips

General Tech Distributor Gear End Float

KVH

Darth Vader
Silver
Country flag
Offline
Factory spec here is about .005 to .007 as I recall. Using the crude "feeler gauge in the pedestal space" test (with a washer under the gear), I'm getting .014. The Manual says to use a packing gasket if there is insufficient end float. What does a person do if the end float is too great, or is that OK?
 

CJD

Yoda
Country flag
Offline
The "packing gasket" is just a thin washer...or use a thicker one than you are currently using.
 

TR4nut

Yoda
Country flag
Offline
I think the float is too much already, right? I've not had that problem, can you see heavy wear on the bronze bushing surface, or maybe some wear marks on the distributor gear? If its possible for you to try, I'd be inclined to swap in a different pedestal assembly, it may be that someone removed some material off the base to give that clearance. I'm not sure how critical it is, but I'd try other options before trying to replace the bronze bushing.
 

TR4nut

Yoda
Country flag
Offline
Had another thought - with the washer trick, take a good look at the washer you used, no burrs, flat etc - I think you could easily have a false measurement using the assumed washer thickness if there was anything making it not lay perfectly flat.
 

dklawson

Yoda
Offline
This is from memory and not specific to a TR4. Please correct me if I am wrong.

I believe the drive gear runs in a steel bushing in the block. The bushing is removable (tap it out from below, knocking it through the entrance for the distributor shaft). You can then tap the bushing back down to a different installed height if the drive gear play is too great with no shims.
 

CJD

Yoda
Country flag
Offline
Also, the car will run fine with .014" float. Extra float can allow the drive gear to lift or bounce under some conditions, which would alter the spark timing a degree or two. For most of us (namely me), a couple degrees of timing is imperceptible. I suppose if the clearance got crazy big, when it bounced it would send an impact load to the oil pump drive shaft, leading to a sheared shaft tab.
 

dklawson

Yoda
Offline
Sidebar (non-Triumph): In college I had an old Toyota Celica with the 18RC engine. The dizzy was driven off a jackshaft that also ran the oil pump. While home on spring break the jackshaft helical gear driving the dizzy "failed". The teeth had worn paper thin. Eventually the teeth "folded over" so the ignition skipped time. Prior to that I had noticed a significant drop in fuel economy. However, I certainly did not expect that my poor gas mileage was due to severe wear in the dizzy drive gears. My spring break plans changed immediately as I scrounged to find a good used jackshaft and install it.
 
Similar threads
Thread starter Title Forum Replies Date
Got_All_4 TR6 Distributor Gear Mounting Question Need End Float Washer Triumph 4
busybrit Healey 3000 distributor drive gear spacer washer, end float! Austin Healey 2
S TR2/3/3A tack drive on the distributor must have caused those cuts in the gear Triumph 4
L TR2/3/3A Noise seemingly from Distributor drive gear Triumph 15
H driving dog [gear] for distributor? Austin Healey 17
B Distributor driving gear orientation Austin Healey 2
R Gear reduction starter hits distributor oil line bolt Austin Healey 14
S TR2/3/3A distributor drive shaft gear Triumph 4
M Distributor Drive Gear MG 10
Dadandson Setting the Distributor Drive Gear.... Spridgets 5
KVH TR4/4A TR4 Timing and Distributor Gear Triumph 3
B B series distributor drive gear. MG 1
B TR4/4A Some Help with Setting Distributor Triumph 47
C MGB New plug wires and distributor cap MG 10
S TR6 '72 TR6 distributor issues Triumph 3
R TR6 Limit Mechanical Advance on TR6 distributor? Triumph 8
M Accuspark distributor Spridgets 2
S TR2/3/3A Distributor vacuum advance hook up to the inner plate Triumph 9
K TR2/3/3A Dr Distributor shipping? Triumph 4
E TR6 Rebuilding Distributor Triumph 2
K TR2/3/3A Distributor internal wires? Triumph 5
KVH General Tech Issues with Distributor--TR4 Triumph 13
PAUL161 T-Series My 55 TF Xpeg Distributor MG 2
C Spitfire Mystery wires - Spit, left near distributor Triumph 2
JPSmit Distributor question Spridgets 0
B MGB 42d4/45d4 distributor MG 0
S TR2/3/3A Installing the distributor pedestal. Triumph 3
A TR6 TR6 Distributor cap issue Triumph 4
C MGA Setting a 123 distributor MG 0
K TR2/3/3A A couple of small distributor tech questions..... Triumph 10
vette Distributor Advance Austin Healey 14
AngliaGT MGB-GT Extremely Dumb Question - Distributor Hose - SOLVED! MG 3
1275GT Wanted 23D4 distributor #40819 Other British Classifieds 0
M TR2/3/3A 25D4 CSI Optimized Distributor Triumph 4
T TR4/4A Why are distributor base plates different, is this a problem? Triumph 7
steveg 100-4 Distributor Internal Ground Wire Austin Healey 6
WJKB-TR6 TR6 '73 Distributor Cap Brush Triumph 5
R Distributor: Reassembling BJ8 Engine Austin Healey 5
Lin Jaguar Distributor Cap for Healey Austin Healey 8
T Pertronix distributor install into Austin Healey 100/6 Austin Healey 12
Lin Distributor to Spark Plug lead wire continuity Austin Healey 5
K TR2/3/3A Do Lucas distributor points still have the" Lucas logo" on them.... Triumph 4
K TR2/3/3A Aftermarket Distributor Points and Terminal Bush leads? Triumph 1
S For Sale TR3 front nose,trunk & petronix distributor Triumph Classifieds 0
P DM6A Distributor Question Austin Healey 9
A TR2/3/3A A123 distributor Triumph 5
AUSMHLY Distributor cap center pin melted Austin Healey 5
M Mallory Dual point distributor Austin Healey 0
K TR2/3/3A Distributor Caps Triumph 6
Csarneson Source for distributor drive peg? Mystery Part? Austin Healey 8

Similar threads

Top