-
The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
-
Hey there Guest!
If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.**Upgrade Now**
(PS: Subscribers don't see this UGLY banner)
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
About to re-install my fuel tank Series I E-Type
- Thread starter Basil
- Start date
Share this page
65_BRG_Sprite
Jedi Warrior
Offline
Have at it! Sometimes the worst tasks aren't so bad after all. Give us photos please.
Gliderman8
Great Pumpkin
Offline
It's a tankless job but you'll get it done.
Geo Hahn
Yoda
Offline
Like one of those metal-wire puzzles I got for Christmas - seems like it won't go until you suddenly find that sweet spot and everything falls into place.
If you have seen the videos then you probably have a pretty fair idea of the sequence.
One thing I did was cut a notch in the fill hose rather than shorten it to get a good connection to both filler and tank:
If you have seen the videos then you probably have a pretty fair idea of the sequence.
One thing I did was cut a notch in the fill hose rather than shorten it to get a good connection to both filler and tank:
Geo Hahn
Yoda
Offline
Now looking at my notes -- I see that the grommets didn't want to stay put as I maneuvered the tank into position. To remedy that I tied them in place using dental floss.
Floss is quite strong yet thin enough to not interfere with the bolts. When all is buttoned up it is slippery enough to slide out after being cut loose.
Floss is quite strong yet thin enough to not interfere with the bolts. When all is buttoned up it is slippery enough to slide out after being cut loose.
OP
Offline
Like one of those metal-wire puzzles I got for Christmas - seems like it won't go until you suddenly find that sweet spot and everything falls into place.
If you have seen the videos then you probably have a pretty fair idea of the sequence.
One thing I did was cut a notch in the fill hose rather than shorten it to get a good connection to both filler and tank:
Brilliant! I've been worried about getting that filler howe up far enough out of the way! I take it that notch allowed you to push the filler hose up farther than normal because the vert pipe comes out of the filler neck?
OP
Offline
Did you use new grommets and spacers? I bought new grommets with new spacers from XKS. The new grommets fit VERY tight on the spacer tubes and in fact I had to figure a way to get them onto the new spacers as I could NOT get the grommets onto the spacer tubes by hand. Once they were on and installed on the tank they were tight! They are not going to be a problem coming loose. Here's a video I made of the process:
Similar threads
Similar threads
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BJ8 transmission mainshaft bearing force needed to install/remove- Started by AUSMHLY
- Replies: 1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
TR2/3/3A Interior rear panel covering gas tank and rear seat bottom install.
- Started by Arrow
- Replies: 7
-
-
TR2/3/3A Steering box install again...the collar with the pinch bolt?
- Started by karls59tr
- Replies: 9
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
D
-
A friendly reminder - be careful what links you click on here. If a link is posted by someone you don't know, or the URL looks fishy, DON'T CLICK. Spammers sometimes post links that lead to sites that can infect your computer, so be mindful what you click.