• A way to modify indicators for TR Sidescreen when R&P Steering is fitted

    I dont think the pictures got transfered. Email me if you want them
    SIDESCREEN TR – TURN SIGNAL INDICATOR AND HORN CONVERSION

    When, during a long telephone conversation, I was negotiating the purchase of the 1958 TR3A, with a guy in Perth, he was telling me that the steering was in A1 condition. That statement made me just a little suspicious because over the years I have owned a few of these cars and found the steering quite prone to wear.
    I eventually went down to Sydney and picked the TR up from the trucking depot, washed off the Nullarbor Plains Sand and proceed to drive it home, across the Blue Mountains.
    During my Evil Knievel type negotiation of the hairpin bends I just knew that the guy wouldn’t pass his Boy Scouts Truth Badge. Then again he was trying to sell it and he was located some 4000 KM away so why not guild the Lilly just a little, or even a lot!
    When I eventually settled down, after that Kamikaze drive, I decided to convert the original single tube steering with a Moss Rack and Pinion Kit.
    I bought a Moto-Litre Steering wheel with the Boss to suit the original TR central Hub and Horn Button arrangement and I knew that it would not be possible to maintain the indicator and Horn Button system. I couldn’t find much out about how others had tackled the problem so the way I figured it out is as follows. It may be of interest.
    Firstly purchase an MGB / Mini combination Trafficator, Horn Push, Headlight Dip and Headlight flash unit. Lucas Part No 39309.

    Drill and Tap Shaft for Dome Nut
    The Moss outer steering tube and inner steering shaft end up, with some fiddling for correct adjustment, in a very good relationship for mounting the Lucas unit on the end of the Tube and the Steering Wheel having just an exact amount of clearance at the bottom of the boss not to foul the Switch.

    MGB Shroud in position
    A 6.5mm hole needs to be drilled at the end of the Tube in order to locate the Switch in a non rotational locking position.
    A 4mm Dome Nut with the threaded part of a matching screw, with head cut off, will act as a cancellation button. This is achieved by drilling and Tapping the Steering Shaft in the correct position and with the aid of Locktite, mount the Dome Nut so it will never vibrate out.
    An MBG Shroud, with some modifications, will house the Lucas Switch. The Shroud needs to be shortened, as shown, but by doing this you lose the bottom two screws, with imbedded nuts, that hold the two halves together.
    This can be overcome by making an Aluminium bracket, mounted with the aid of three Screws. One Screw locates to the Steering Tube and the other two hold the two halves together at the bottom end.
    A little bit of reliving of the Plastic is also required to clear the Speedometer Glass Face.
    If you really want to bring the car into the 1990’s you can remove the foot operated Headlight Dimmer and transfer the wiring to the Lucas Switch as well as giving you a Horn Push and even a Headlight Flash which saves one lifting a finger from the Steering Wheel in order to give recognition to that oncoming TR.
    Certain Relays are required for this and in my opinion the introduction of some much needed additional fuses and other operating Relays makes the car very thankful.

    I am only too pleased to offer any other comments or assistance if required.
    Ian Simmons
    RYLSTONE NSW
    AUSTRALIA

    Aluminium Bracket
    Aluminium Bracket
    secsimmo@bigpond.com







    Cut off MGB Shroud
    Dome Nut


    Cut off MGB Shroud
    Cut off MGB Shroud
    Cut off MGB Shroud
    Cut off MGB Shroud






  • Recent Articles

    Editor_Reid

    Matching Funds for Healey Museum Donations

    Some of you may already be aware that the Healey Museum in The Netherlands recently issued an invitation to Healey clubs to participate in a new fundraising effort to support its long-term future. For... read more
    Editor_Reid 11-25-2018, 01:43 PM
  • Recent Forum Posts

    Alfred E. Neuman

    Re: Audi A4?

    Unless he enjoys many, many, many trips to the repair shop, avoid used modern German cars.

    Alfred E. Neuman Today, 08:43 AM Go to last post
    NutmegCT

    Audi A4?

    Friend is looking for a used Audi A4 for his son. Son is 27, married, and prefers an automatic trans.

    I wondered if anyone here has thoughts

    NutmegCT Today, 08:05 AM Go to last post
    Lou Metelko

    Re: TR2 color questions

    If you go to the above link it will open to a shot of my dearly beloved TS981. Believe it or not but that is the photo rendition of Ice Blue in direct

    Lou Metelko Today, 01:54 AM Go to last post
    dougie

    Re: Holley fuel regulator questions

    Ditto

    dougie Today, 12:48 AM Go to last post
    dklawson

    Re: Holley fuel regulator questions

    I believe you are over thinking this.

    Leave all the regulator housing screws fully tightened. (Loosening them will 1) allow leaks, and

    dklawson Today, 12:34 AM Go to last post
  • Recent Blog Posts

    Peko

    Triumph surrey top

    I’m looking for a original or repop surrey top for my newly inherited 1963 TR4. Any leads or info would be greatly appreciated. Thank you Casey 510 610 5325

    Peko 12-01-2018 11:37 PM
  • Twitter